AUT

CYPECAD's AUT module has two options available that have been created to automatically generate the structure: Import of IFC files from CAD/BIM programs and Interpretation of DXF and DWG files.

C3D

The C3D module is the basic core of CYPECAD's tools and is required for the operation of all the program versions.

ECL

The ECL module is compatible with CYPECAD and allows the program to analyse and design the reinforcement of stair slabs as isolated elements of the structure.

ENZ

Using the ENZ module, CYPECAD and CYPE 3D can design foundations resolved using piles with their respective pile caps. This module also designs strap and tie beams spanning between the pile caps.

FPT

The CYPECAD module FPT, allows users to design the passive reinforcement of waffle slabs, in-situ joist floor slabs and their perimeter beams.

LFL

The LFL module allows CYPECAD to analyse and design mat foundations and foundation beams accurately and in accordance with structural design standards.

LMA

The LMA module is compatible with CYPECAD and allows the program to analyse and design flat slabs.

LPS

CYPECAD's LPS module has been designed to carry out the design of the passive reinforcement of post-tensioned slabs, using the forces that have been obtained from analysing the post-tensioned tendons (bonded or unbonded), whose properties have been introduced by the program users.

MAP

The MAP module is compatible with CYPECAD and allows the program to analyse and design concrete block masonry walls.

MTP

CYPECAD’s module: MTP, designs reduced thickness reinforced concrete walls with a single reinforcement plane, which are used as load bearing walls to support vertical loads and also resist horizontal forces acting in the plane of the wall.

MUS

The MUS module is compatible with CYPECAD and allows the program to analyse and design concrete walls and masonry walls.

PAN

The PAN module allows users to analyse and design reinforced concrete shear walls in CYPECAD.

PHA

Using the PHA module, CYPECAD and CYPE 3D design rectangular and circular reinforced concrete columns.

PMT

With the PMT module, steel columns can be introduced into CYPECAD so that they can be designed and built up according to the code selected.

PPA

The PPA module is compatible with CYPECAD and allows the program to analyse and design hollow core floor slabs.

PUN

With the PUN module, CYPECAD checks the Failure Limit State of concrete for punching shear in flat slabs, waffle slabs and mat foundations using two methods.

Q04

With the Q04 module and computers equipped with several parallel processors, users can save a significant amount of time in the analysis process of the associated programs.

RET

The RET module is used to analyse and design waffle slabs in CYPECAD.

RMP

The RMP module is compatible with CYPECAD and allows the program to analyse and design ramp slabs as isolated elements of the structure.

SI6

The SI6 module carries out, in CYPECAD and CYPE 3D, the fire resistance check and design of sections or protection cover depending on the material in question.

UNF

The UNF module is compatible with CYPECAD and allows the program to analyse and design reinforced and prestressed precast joist floor slabs.

UNI

Using the UNI module, users can analyse and design generic concrete joist floor slabs.

UNS

The UNS module is compatible with CYPECAD and allows users to analyse and design joist floor slabs with joists fully assembled on site.

VHA

The VHA module is for use in CYPECAD and CYPE 3D and allows users to introduce and design various types of concrete beams.

VMT

With the VMT module, the following types of beams can be introduced and designed: steel beams below a floor slab or aligned with its upper face and composite steel beams linked to the floor slab with connectors.

ZAP

In CYPECAD and CYPE 3D, the ZAP module can be used to design foundations made of reinforced concrete rigid footings or mass concrete footings, either isolated or combined, tie and strap beams between footings and, in CYPECAD, strip footings for walls.

ZCA

In CYPECAD, the ZCA module is used to design foundations with special element intersections, establish polygonal limits of footings, and apply loads on footings, pile caps and strap and tie beams. In CYPE 3D, it facilitates the layout of polygonal limits for footings.